Holikme 30 Feet Dryer Vent Cleaner Kit, Flexible Lint Brush with Drill Attachment, Fireplace Chimney Brushes Extends Up to 30 Feet for Easy Cleaning, Use with or Without a Power Drill

This did a great job cleaning out my dryer vent and saved me a ton of money compared to having a company come out to do this for me. My vent pipe is roughly 25' long and has several 90 degree bends. This kit was flexible enough to make it around the bends and clean my entire dryer vent pipe. It was very easy to assemble and use; however since it's attached to a drill it's basically tightening the pieces together as it moves through the vents. I had to use two pair of pliers to get the sections apart when I was through.

After having to call someone in to clean the dryer air duct wanted to see how hard it would be to do it myself.Very easy to assemble, attaching lengths of rod as you go to travel the length of the duct. Follow the instructions to ensure that you only rotate it around in the correct direction to ensure that you don't unscrew the rods and it come undone within the duct.Can be purchased with different amounts of lengths of rod to ensure that you can reach the end of your duct. It all unscrews so that it can be stored easily until it is needed.A great value for money instead of having to call someone in to do the job for you that only takes a short time to do yourself.

Good product. Would be so much better if it had a storage case or bag. This rod has good flexibility that allows for the operator to use the drill in one hand and push/pull the flex rod with the other hand. As your drill is spinning the rod, push the rod in about 2’ and pull backwards that same distance in a continuous motion time 4-6 times. After you clean a distance of about 6’, completely pull the rod/brush out in order to remove lint build up. Repeat. You will be amazed how much lint will come out. Run the dryer afterwards for a few minutes. This will blow out the fine dust.You will need two pair of pliers to disassemble each of the rods due to the drill causes the fittings to tighten. Just gently grip the male and female with the pliers and a tiny reverse twist to break the tightness.

A must have for Dryer Duct cleaning.Great Value for the DIY work.Quality and very easy to use,Put it into the Inlet side ( Dryer Duct ) and run your drill clockwise only thru to Outlet side.Pro tip- after run your Leaf Blower on low intoThe Inlet side and push out remaining debris 👍🏼🧰

We never thought there was much lint collecting inside our 20' dryer duct. Our dryer seem to keep taking longer and longer to dry clothes which we attributed to it being 8 years old. I even blew out the duct using a gas powered blower which removed some lint (I thought it removed it all).A year later the washer went out (it was a stackable unit) and we bought a new washer/dryer stack. We thought we bought a lemon because there was a ton of condensation coming out of the dryer vent and it was taking forever to dryer.Enter the Dryer Vent Cleaner Kit. I bought this 8 months ago thinking at some point I would clean out the little bit of lint that was in the ducting. The day the new dryer was installed I removed the dryer to access the vent. I inserted the dryer cleaner which pulled out a few large clumps of lint, but then stopped 1/3 of the way through (leaving one of the 1' connectors twisted - much like some have posted pictures of). I then went to the other end of the line and did the same thing removing more lint, but stopping 1/3 of the way through. I thought "Great, I cleared the vent!"That evening dryer loads were still taking forever to dry (never really drying) and condensation around the vent was off the charts.At this point I realized that I need to run this cleaner through the entire line. Instead of push it through which creates the twisting of the segments and would never go all the way through for me, I decide to pull it through.To do this I had a pull a string through the vent then tape the end of the segments that connects to the drill and pull that through until the brush it at the beginning of the vent. I watched a video by an electrician who showed how to suck a fishing line with a small plastic bag (like a parachute) through the duct. As I used the shop vac on on end the bag+fishing line was not coming out, but I was getting a bunch of lint coming out. I went to the other end to try the same thing with the shop vac and got a ton of lint, but not the fishing line+bag until suddenly enough lint cleared that the bag and line came through.I used that to pull a strong string through and then attached the end of the string to the drill end of the vent cleaner rod. Once the end was sticking out, I attached the drill, turn it on, and slow started pulling. The result was miraculous. No bent segments, the pulled through seamlessly, and in the process brought out another ton more of lint (a lot of it went due to the ongoing condensation caused by restricted flow).The trick is to set the cleaner so that you can PULL it through no push it through the duct.New dryer is drying flawlessly. I plan to run the cleaner through the duct once every 6 months and use my shop vac once a month to gauge how frequently I need to clean the vent.Amazing results!

Wow, my dryer was not drying well, everything checked out fine with the actual dryer.I used this brush in the vent hose from the dryer side, and a fair amount of lint came out.I then used the brush from the exterior side, and it pulled out enough lint to fill a box.The brush connected to my drill and I found it easiest to add 2 segments at a time.The drill must turn clockwise while entering and exiting the duct. I used a couple of rubber jar openers to twist the rods apart, when done. The included gloves were a nice bonus. Highly recommended!

First off, this is functional and worked to clean out my dryer duct which was the end result I was looking for when I bought this 30' duct cleaning kit; and for the price I cannot complain too much. However, the nylon rods connect to one another via threads which makes them difficult to disconnect from each other without two pliers. Would have much preferred they offer this product with the detent style quick connectors so that as you use the product it does not force the nylon rods to get tighter and tighter connected to each other. Overall this item worked just could be a more user friendly.

The media could not be loaded. Did exactly what I wanted it to do. Doesn’t feel cheap, is simple to use, worked flawlessly, and cleaned out my vent. The best part is I can use it again in the future. My only recommendation is to make it a two person job. It just makes it easier having one person feed it through the vent while the other person is squeezing the drill behind the first person and also feeding it. Doing so helps mitigate ant twists in the line as it’s going down the vent